F41 Short Nut SAE J512 #010110 SAE 45°flare Fittings Adapter Connector 20910 41FS 1110 N1 41FX 441S L
SAE #010110
| PART# | TUBE O. D | C | D | L |
| F41-02 | 1/8 | 3/8 | .133 | .50 |
| F41-03 | 3/16 | 7/16 | .195 | .62 |
| F41-04 | 1/4 | 9/16 | .258 | .75 |
| F41L-04 | 1/4 | 1/2 | .258 | .75 |
| F41-05 | 5/16 | 5/8 | .320 | .88 |
| F41-06 | 3/8 | 3/4 | .383 | 1.00 |
| F41L-06 | 3/8 | 3/4 | .383 | .88 |
| F41-07 | 7/16 | 13/16 | .445 | 1.06 |
| F41-08 | 1/2 | 7/8 | .508 | 1.12 |
| F41L-08 | 1/2 | 7/8 | .508 | .93 |
| F41-10 | 5/8 | 1-1/16 | .633 | 1.31 |
| F41-12 | 3/4 | 1-1/4 | .758 | 1.50 |
| Part# | Thread SizeUNF | Thread | A | Hex | Approx.Wt.Lbs. |
| 10-013 | 1/8″ | 5/16-24 | 0.5 | 0.37 | 0.01 |
| 10-014 | 3/16″ | 2003/8/24 | 0.62 | 0.43 | 0.02 |
| 10-015 | 1/4″ | 7/16-20 | 0.75 | 0.56 | 0.03 |
| 10-015L | 1/4″ | 7/16-20 | 0.75 | 0.5 | 0.03 |
| 10-016 | 5/16″ | 2001/2/20 | 0.88 | 0.62 | 0.04 |
| 10-017L | 3/8″ | 2005/8/18 | 0.88 | 0.75 | 0.05 |
| 10-017 | 3/8″ | 2005/8/18 | 1 | 0.75 | 0.04 |
| 10-018 | 7/16″ | 11/16-16 | 1.06 | 0.81 | 0.06 |
| 10-019L | 1/2″ | 2003/4/16 | 0.93 | 0.87 | 0.06 |
| 10-019 | 1/2″ | 2003/4/16 | 1.12 | 0.87 | 0.09 |
| 10-020L | 5/8″ | 2007/8/14 | 1.08 | 1 | 0.1 |
| 10-020 | 5/8″ | 2007/8/14 | 1.31 | 1.06 | 0.15 |
| 10-021 | 3/4″ | 1-1/16-14 | 1.5 | 1.25 | 0.24 |
| 10-022 | 7/8″ | 1-1/4-12 | 1.62 | 1.5 | 0.36 |
| 10-026 | 1″ | 1-3/8-12 | 1.81 | 1.62 | 0.44 |
Interchangeability for reference
Parker : 41FS-2 41FS-3 41FS-4 41FS8 41FX-6 41FS-7 41FS-8 41FX-8 41FS-10 41FX-10 41FS-12 41FS-14
Eaton : 1110×2 1110×3 110×4 1110×5 1110×6 1110×7·1110×8 1110×10 1110×12*
Midland : 10-013 10-014 10-015 10-015L 10-016 10-01 10-017 10-018 10-019L 10-019 10-020L 10-020 10-021 10-022 10-026
attention please ：Quotations and delivery of non-stock items supplied on request. Configurations and dimen sions subject to change without notice. Additional information can be found in SAE J530 Automotive Pipe Fittings and SAE J531 Drain Plugs.
Actual O.D. of Flare Fittings
SAE 45° Flare Fittings & Adapters
Industry Standard - SAE J512 45° Flare
Specification
- Temperature Range: -65°F to +250°F (-53°C to +121°C) range at maximum operating pressures.
- Working Pressure: up to 2000 psi depending on tube size. Will withstand burst pressure of standard tubing – up to 5000 psi with bundy-weld (double flared) and 3500 psi with copper tubing, depending on size. Obviously, Temperature and type of tubing used are important factors.
Installation Instructions
- Cut tubing to desired lenght. Make sure all burrs are removed and ends are cut square.
- Slide nut on tube. Threaded and “A” of nut must face out.
- Flare end of tube with a 45° flaring tool. a-Measure flare diameter b-Examine flare for excessive thin out.
- Lubricat threads and assemble to fitting body. Nut should be turned hand out.
- Tighten assembly with wrench until a solid feeling is encountered. From that point, apply a one-sixth turn.
SAE 45 Degree Flare Fittings – Brass Material
Applications
LP and natural gas, flammable liquids, instrumentation, refrigeration, power steering, hydraulic and pneumatic systems. Used on low, medium and high pressure lines under the most adverse conditions, compatible with copper, brass, aluminum and steel hydraulic tubing that can be flared.
Features
- Construction – Two piece body and nut, straight barstock & forged fittings.
- Good Vibration resistance – use long nut when greater vibration resistance is required.
- Conformance – Heavy duty flare fittings are manufactured to SAE specifications, Meets specifications and standards of ASA, ASME, SAE, and MS (Military standards).
- Reusability – Can be assembled and re-assembled repeatedly & Resists mechanical pull-out.
Copper, brass, aluminum and steel hydraulic tubing that can be flared.
Tolerance
+/- .03 on all dimensions. Dimension data can change without notice. Please call us when dimensions are critical.
