F48 Male Pipe SAE J512 #010102 SAE 45°flare Fittings Adapter Connector U1 48

 SAE #010102

Interchangeability for reference

Parker : 48F-2-2 48F-3-2 48F-3-4 48F-4-2 48F-4-4 48F-4-6 48F-4-8 48F-5-2 48F-5-4 48F-5-6 48F-6-2 48F-6-4 48F-6-6 48F-6-8 48F-6-12 48F-8-4 48F-8-6 48F-8-8 48F-8-12 48F-10-4 48F-10-6 48F-10-8 48F-10-12 48F-12-8*48F-12-12*48F-14-12*

Eaton/WeatherHead : 48×2 48×3 48×4 48x4x4 48×5 48x5x4 48x6x2 48×6 48x6x6 48x6x8 48x8x4 48×8 48x8x8 48x10x6 48×10 48×12 48x12x12

Midland : 10-253 10-254 I023ST 10-255 10-256L 10-256 10-257 10-258 10-259L 10-259 10-260L 10-260 10-261 10-262 10-263L 10-263 10-264 10-264 10-265 10-265 10-266 10-267 10-268L 10-268 10-209L 10-20 10-270 10271 10-272L 10-272 10273L 10-273 10-274 10-275 10-276 10-277 10-278 10-279 10-280

attention please ：Quotations and delivery of non-stock items supplied on request. Configurations and dimen sions subject to change without notice. Additional information can be found in SAE J530 Automotive Pipe Fittings and SAE J531 Drain Plugs.

Actual O.D. of Flare Fittings

SAE 45° Flare Fittings & Adapters

Industry Standard - SAE J512 45° Flare

Specification

1. Temperature Range: -65°F to +250°F (-53°C to +121°C) range at maximum operating pressures.
2. Working Pressure: up to 2000 psi depending on tube size. Will withstand burst pressure of standard tubing – up to 5000 psi with bundy-weld (double flared) and 3500 psi with copper tubing, depending on size. Obviously, Temperature and type of tubing used are important factors.

Installation Instructions

1. Cut tubing to desired lenght. Make sure all burrs are removed and ends are cut square.
2. Slide nut on tube. Threaded and “A” of nut must face out.
3. Flare end of tube with a 45° flaring tool. a-Measure flare diameter b-Examine flare for excessive thin out.
4. Lubricat threads and assemble to fitting body. Nut should be turned hand out.
5. Tighten assembly with wrench until a solid feeling is encountered. From that point, apply a one-sixth turn.

SAE 45 Degree Flare Fittings – Brass Material

Applications

LP and natural gas, flammable liquids, instrumentation, refrigeration, power steering, hydraulic and pneumatic systems. Used on low, medium and high pressure lines under the most adverse conditions, compatible with copper, brass, aluminum and steel hydraulic tubing that can be flared.

Features

1. Construction – Two piece body and nut, straight barstock & forged fittings.
2. Good Vibration resistance – use long nut when greater vibration resistance is required.
3. Conformance – Heavy duty flare fittings are manufactured to SAE specifications, Meets specifications and standards of ASA, ASME, SAE, and MS (Military standards).
4. Reusability – Can be assembled and re-assembled repeatedly & Resists mechanical pull-out.

Copper, brass, aluminum and steel hydraulic tubing that can be flared.

Tolerance

+/- .03 on all dimensions. Dimension data can change without notice. Please call us when dimensions are critical