71 Male Run Tee SAE # 060424BA Brass Compression Fittings 71 171C BST3
SAE 060424BA 71 171C BST3
|
PART# |
TUBE O.D×MALE NPTF | M | N | D |
| 71-03-02 | 3/16×1/8 | .63 | .69 | .125 |
| 71-04-02 | 1/4×1/8 | .63 | .75 | .188 |
| 71-04-04 | 1/4×1/4 | .69 | .88 | .188 |
| 71-05-02 | 5/16×1/8 | .72 | .75 | .250 |
| 71-05-04 | 5/16×1/4 | .75 | .88 | .250 |
| 71-06-02 | 3/8×1/8 | .75 | .75 | .312 |
| 71-06-04 | 3/8×1/4 | .79 | .87 | .312 |
| 71-06-06 | 3/8×3/8 | .88 | 1.00 | .330 |
| 71-08-06 | 1/2×3/8 | .94 | 1.09 | .406 |
| 71-08-08 | 1/2×1/2 | .97 | 1.19 | .406 |
| 71-10-08 | 5/8×1/2 | 1.06 | 1.31 |
.500 |
nterchangeability for reference
Parker : 171C-2-2 171C-32 171C-4-2 171C-4-4 171C-64
Eaton/WeatherHead : 71×3 71×4 71×6
Midland : 18-272 18-273 18-274 18-275 18-276 18-277 18-278 18-279 18-280 18-281 18-282 18-283 18-284
attention please ：Quotations and delivery of non-stock items supplied on request. Configurations and dimen sions subject to change without notice. Additional information can be found in SAE J530 Automotive Pipe Fittings and SAE J531 Drain Plugs.
Brass Compression Fittings & Adapters
Applications
Compatible with copper, brass, aluminum and thermoplastic tubing for instrumentation, hydraulic and pneumatic systems like typical fluid air, oil, water, lubricant and other applications.
Note: When use with thermoplastic tubing, a brass insert is required for support.
Features
- Construction – Three piece unit: body, nut (available with long or short nut) and sleeve. Extruded and Forged Configuration.
- Vibration resistance – Fair vibration resistance with short nut, The long nut can be used for greater vibration application.
- Advantages – Low cost. Easy to assemble without special tube prep, no flaring.Broad selection of styles and sizes.
Specification
- Temperature Range: -65°F to +250°F (-53°C to +121°C) range at maximum operating pressures.
- Working Pressure: up to 2000 PSI with a 4:1 safety factor depending on tube sizes. When using plastic tubing, use the working pressure for type used.
Assembly Instructions
- Cut tubing to desired length.
- Slide nut and then sleeve on tube. Threaded end “A” of nut must face out.
- Insert tubing into fitting body. Be sure tubing is bottomed on fitting shoulder.
- Lubricate threads and assemble to fitting body.
- Tighten nut hand tight. From that point, tighten with a wrench the number of turns indicated in the chart (For Fractional Tubes) below.
|
TUBE SIZE
|
Additional Turns From Hand Tight
|
|
1/8” thru 1/4”
|
1-1/4
|
|
5/16”
|
1-3/4
|
|
3/8” thru 1”
|
2-1/4
|
US Brass Compression Fittings & Adapters
- Extruded Bar Stock, Hex Forging Blank, Fractional Tube Dia & NPT Thread Mainly.
Euro Brass Compression Fittings & Adapters
- Extruded Bar Stock, Round Forging Blank, Nickel-Plated, Metric Tube Dia & BSP Thread Mainly.
