3200 Reduce Connector SAE# 130139 US Brass Pipe fittings & Adapters 375 222P 3200 R1 120AH 120B
*Ref.SAE.NO.130138
| PART# | Thread size | C | L |
| 3200L-BA | 1/4×1/8 | 5/8 | .83 |
| 3200-BA | 1/4×1/8 | 3/4 | .97 |
| 3200-CA | 3/8×1/8 | 7/8 | .94 |
| 3200L-CB | 3/8×1/4 | 13/16 | 1.00 |
| 3200-CB | 3/8×1/4 | 7/8 | 1.16 |
| 3200L-DA | 1/2×1/8 | 15/16 | 1.19 |
| 3200L-DB | 1/2×1/4 | 1″ | 1.11 |
| 3200-DB | 1/2×1/4 | 1-1/16 | 1.28 |
| 3200L-DC | 1/2×3/8 | 15/16 | 1.19 |
| 3200-DC | 1/2×3/8 | 1-1/16 | 1.38 |
| *3200-EC | 3/4×3/8 | 1-3/8 | 1.32 |
| *3200-ED | 3/4×1/2 | 1-3/16 | 1.19 |
Interchangeability, for, reference
Parker :222P-2-2 222P-4-2 222P-4-4 222P-6-2 222P-6-4 222P-6-6 222P-8-4 222P-8-6 222P-8-8 222P-12-6 222P-12-8 222P-12-12
Eaton :3200×2 3200x4x2 3200×4 3200x6x4 3200×6 3200x8x6 3200x12x6 3200x12x8
Midland :28-190L 28-190 28-191L 28-191 28-192L 28-192 28-198 28-193L 28-193 28-194L 28-194 28-199 28-195L 28-195 28-196 28-207 28-208 28-209
attention please ：Quotations and delivery of non-stock items supplied on request. Configurations and dimen sions subject to change without notice. Additional information can be found in SAE J530 Automotive Pipe Fittings and SAE J531 Drain Plugs.
Brass Compression Fittings & Adapters
Applications
Compatible with copper, brass, aluminum and thermoplastic tubing for instrumentation, hydraulic and pneumatic systems like typical fluid air, oil, water, lubricant and other applications.
Note: When use with thermoplastic tubing, a brass insert is required for support.
Features
- Construction – Three piece unit: body, nut (available with long or short nut) and sleeve. Extruded and Forged Configuration.
- Vibration resistance – Fair vibration resistance with short nut, The long nut can be used for greater vibration application.
- Advantages – Low cost. Easy to assemble without special tube prep, no flaring.Broad selection of styles and sizes.
Specification
- Temperature Range: -65°F to +250°F (-53°C to +121°C) range at maximum operating pressures.
- Working Pressure: up to 2000 PSI with a 4:1 safety factor depending on tube sizes. When using plastic tubing, use the working pressure for type used.
Assembly Instructions
- Cut tubing to desired length.
- Slide nut and then sleeve on tube. Threaded end “A” of nut must face out.
- Insert tubing into fitting body. Be sure tubing is bottomed on fitting shoulder.
- Lubricate threads and assemble to fitting body.
- Tighten nut hand tight. From that point, tighten with a wrench the number of turns indicated in the chart (For Fractional Tubes) below.
|
TUBE SIZE
|
Additional Turns From Hand Tight
|
|
1/8” thru 1/4”
|
1-1/4
|
|
5/16”
|
1-3/4
|
|
3/8” thru 1”
|
2-1/4
|
US Brass Compression Fittings & Adapters
- Extruded Bar Stock, Hex Forging Blank, Fractional Tube Dia & NPT Thread Mainly.
Euro Brass Compression Fittings & Adapters
- Extruded Bar Stock, Round Forging Blank, Nickel-Plated, Metric Tube Dia & BSP Thread Mainly.
